 |
Sealcon CD07GA-GY: Gray Nylon Enlarged-Body Cable Gland, PG 7 / 1/4 in. NPT, 4–8 mm Cable
Gray Nylon 6/6 enlarged-body cord grip for 0.16–0.31 in. (4–8 mm) cable and a compact PG 7 / 1/4 in. NPT panel entry. It allows a larger cable jacket to enter the gland while the conductors pass through the smaller threaded opening.
✅ Enlarged Cable Range with a Compact Thread
Choose the CD07GA-GY when the cable outside diameter is 0.16–0.31 in. (4–8 mm) but the available enclosure entry is PG 7 / 1/4 in. NPT. The enlarged gray nylon body maintains a liquid-tight strain-relief interface for the larger cable jacket.
Adapt Larger Cable to Restricted Enclosure Entries
The Sealcon CD07GA-GY enlarged-body cable gland addresses installations where the cable diameter increases but the thread size must remain compact. Gray Nylon 6/6 construction resists corrosion, and the Buna-N seal protects the entry from moisture and contaminants.
Patented overlapping clamping splines press concentrically around the cable to provide pull-out resistance without damaging the jacket. The recessed grommet stays protected inside the dome, and compatible standard or reduced inserts can be exchanged when the application requires another supported opening.
↔️ 4–8 mm Cable
Enlarged body accepts a larger cable jacket at a PG 7 / 1/4 in. NPT entry
💧 NEMA 4X/6
IP68/IP69K sealing, 300 ft. submersion, and 150 psig capability
⚙️ Concentric Clamping
Overlapping splines provide even pull-out resistance around the jacket
◻️ Gray Nylon 6/6
Corrosion-resistant body with a Buna-N seal for industrial environments
Key Features & Benefits
- Enlarged-Body Design: Accommodates 0.16–0.31 in. (4–8 mm) cable at a compact entry
- PG 7 / 1/4 in. NPT Thread: Fits common small enclosure openings
- Liquid-Tight Protection: Rated NEMA 4X and 6, IP68 and IP69K, and submersible to 300 ft.
- Concentric Strain Relief: Applies even cable-retention force
- Pressure Rating: Rated to 150 psig (10 bar)
- Vibration-Resistant Dome: Helps the fitting maintain clamping force on machinery
- Chemical Resistance: Resists salt water, acids, alkalis, gasoline, and oils
- Sold Individually: Locking nut and O-ring are sold separately
Specifications
|
Part Number
|
CD07GA-GY
|
|
Brand
|
Sealcon
|
|
Alternate Part Number
|
Hummel 1.590.0700.14
|
|
Product Type
|
Enlarged-body cable gland / cord grip
|
|
Color
|
Gray
|
|
Thread Size
|
PG 7 / 1/4 in. NPT
|
|
Cable O.D. Range
|
0.16–0.31 in. (4–8 mm)
|
|
Through-Hole Diameter
|
0.49 in. (12.5 mm)
|
|
Body Length
|
0.87 in. (22 mm)
|
|
Thread Length
|
0.28 in. (7 mm)
|
|
Wrench Flat — Dome
|
0.75 in. (19 mm)
|
|
Wrench Flat — Body
|
0.75 in. (19 mm)
|
|
Body Material
|
Nylon 6/6
|
|
Seal
|
Buna-N
|
|
Environmental Ratings
|
NEMA 4X and 6; IP68 and IP69K; submersible to 300 ft.
|
|
Pressure Rating
|
150 psig (10 bar)
|
✅ Approvals & Compliance
- RoHS compliance
- Deca-BDE compliance
- REACH compliance
- WEEE compliance
- UL / cUL Listed
- UL Registered
- EAC
- CE
- German Lloyd
📏 Verify Jacket and Entry Dimensions
Confirm that the cable O.D. is 0.16–0.31 in. (4–8 mm), the conductors can pass through the 0.49 in. (12.5 mm) through-hole, and the panel entry is PG 7 / 1/4 in. NPT. Standard and reduced inserts may be available separately.
🔧 Installation Notes
Confirm conductor passage: Make sure the conductors and termination arrangement fit through the narrower entry section.
Position the cable jacket: Place the outer jacket inside the enlarged clamping and sealing area.
Install separate hardware: Use a compatible locking nut and O-ring when required; both are sold separately.
🏭 Typical Applications
Control panels with restricted entry sizes
Larger sensor and actuator cables
Machine and process equipment
Outdoor electrical enclosures
|
|
|
