 |
 |
 |
|
Saginaw SCE-8066CHNF Continuous Hinge Steel Enclosure: 8.13" H x 6" W x 6" D, NEMA 4 and IP66
Industrial continuous hinge electrical enclosure made from 0.063" carbon steel with an ANSI 61 gray powder-coated finish. Built for junction-box, terminal-enclosure, and control-box applications that require welded construction, an oil-resistant gasket, and recognized environmental ratings.
✅ Industrial Electrical Enclosure for Protected Wiring and Controls
The Saginaw Control & Engineering SCE-8066CHNF is designed for use as a junction box, terminal enclosure, or industrial control box. Its 8.13" H x 6" W x 6" D dimensions provide a defined enclosure size for planning wall space, wire routing, and internal component placement.
Reliable Carbon Steel Protection for Industrial Electrical Equipment
The SCE-8066CHNF combines 0.063" carbon steel with continuously welded, ground-smooth seams to form a rigid enclosure for electrical connections and control equipment. An ANSI 61 gray powder coating protects the steel surface, while the oil-resistant door gasket helps maintain the enclosure seal in demanding industrial locations.
A full-length continuous hinge with stainless steel hinge pins supports dependable door movement, and one outside screw clamp secures the door. Its practical cabinet size supports junction-box wiring, terminal blocks, and compact control components while keeping the installation organized and protected. The enclosure has no holes or knockouts, allowing installers to place cable entries and device openings according to the application.
🛡️ NEMA and IP66 Protection
Recognized ratings support indoor and outdoor industrial enclosure applications when installed according to the required instructions
🚪 Continuous Hinge Door
A full-length hinge with stainless steel pins supports consistent alignment and repeated access to enclosed components
⚙️ Installation Ready
Welded rear mounting provisions, grounding studs, and an undrilled body support application-specific installation
🎨 ANSI 61 Gray Finish
Powder-coated 0.063" carbon steel provides a durable surface for industrial electrical environments
Key Features & Benefits
- Welded Carbon Steel Construction: 0.063" carbon steel body with continuously welded seams that are ground smooth
- No Factory Holes or Knockouts: Allows application-specific placement of conduit, cable, and device openings
- Screw-Clamp Door: Door is secured by one outside screw clamp
- Oil-Resistant Gasket: Helps seal the door opening against environmental exposure
- Subpanel Mounting Preparation: Standoffs for mounting optional subpanels are included; subpanels are sold separately
Specifications
| Part Number | SCE-8066CHNF |
|---|
| Manufacturer | Saginaw Control & Engineering |
|---|
| Enclosure Type | Continuous hinge electrical enclosure |
|---|
| Dimensions | 8.13" H x 6" W x 6" D |
|---|
| Metric Dimensions | 206.502mm x 152.4mm x 152.4mm |
|---|
| Material | 0.063" carbon steel |
|---|
| Finish | ANSI 61 gray powder coating |
|---|
| Door Closure | One outside screw clamp |
|---|
| Hinge | Continuous hinge with stainless steel pins |
|---|
| Gasket | Oil resistant |
|---|
| Factory Openings | No holes or knockouts |
|---|
| Subpanel Provisions | Standoffs included; subpanel sold separately |
|---|
📋 Environmental Ratings and Certifications
NEMA: Type 3R, 4, 12, and 13
UL Listed: Type 3R, 4, and 12
CSA: Type 3R, 4, and 12
IEC 60529
IP66
⚠️ Type 3R Installation Notice
Special instructions apply to IS3, IS4, and IS6 configurations to maintain the Type 3R environmental rating. Follow the instructions located on the enclosure door.
🔧 Installation and Panel Notes
Panel preparation: Subpanel standoffs are included, while the subpanel itself is sold separately.
External mounting: Mounting provisions are welded to the enclosure back at the top and bottom.
Grounding: Use the ground studs on the door and body as required by the installation design and applicable electrical codes.
|
|
|
 |
|
 |
|
