 |
 |
 |
|
Sealcon M16 Female Signal Rear Mount Panel Connector with Flange, 10 Pin, 1 mm Contacts, 5-9 mm Cable, IP67 / IP69K
M16 female signal rear mount panel connector with flange with 10 pin insert, 1 mm crimp contacts, 28-18 AWG wire range, 5-9 mm cable range, 8 Amps / 160V, IP67 / IP69K.
Why Choose this Sealcon M16 Connector?
The Sealcon M16-FRM10P59 is an M16 female signal rear mount panel connector with flange with a 10 pin insert for 1 mm crimp contacts. It uses a nickel plated brass housing, brass alloy contacts, and a 5-9 mm cable range for sealed industrial signal wiring.
Rated IP67 / IP69K, this unassembled connector includes the housing, insert, and crimp contacts needed for field termination. It is a practical choice for panel-mounted industrial signal wiring that requires strain relief.
🔌 10 Pin Insert
Built for 10 M16 signal connections with crimp contact termination
📏 5-9 mm Cable Range
Accepts 5-9 mm cable for sealed field wiring and connector assembly
🛡️ IP67 / IP69K Protection
Sealed for demanding industrial environments where moisture and washdown resistance matter
🔩 Rear Mount Flange
Flanged panel-mount design includes strain relief for secure signal wiring
⚠️ Confirm Pin Count, Contact Size, and Cable Range
Before ordering, confirm the mating thread, orientation, insert layout, crimp wire gauge, cable outside diameter, nominal current, and nominal voltage match the equipment being wired.
This connector uses a M16 mating thread, 28-18 AWG crimp wire gauge, and a 5-9 mm cable range.
No special contact insertion/removal tool is listed for this configuration.
📋 Connection and Assembly Notes
The Sealcon M16-FRM10P59 is supplied unassembled so the housing, insert, and crimp contacts can be assembled during wiring. Crimp the contacts to the correct wire gauge, seat the contacts in the insert, verify Euro-Lock retention, and route the cable through the housing before final tightening.
Key Features & Benefits
- 10 pin insert for crimp contacts
- 1 mm contact size
- Accepts 5-9 mm cable
- 28-18 AWG crimp wire gauge
- 8 Amps nominal current rating
- 160V nominal voltage rating
- No tools needed to insert or remove contacts
- Euro-Lock keeps contacts in position
- EMI shielding
- Features strain relief
- Nickel Plated Brass housing
- Gold Plated Nickel contact surface
- M16 mating thread
- IP67 / IP69K protection rating
Technical Specifications
|
Product Code
|
M16-FRM10P59
|
|
Brand
|
Sealcon
|
|
Product Type
|
M16 Rear Mount Panel Connector
|
|
Housing
|
Nickel Plated Brass
|
|
Housing Dimensions
|
1.81" Length x 0.78" Width x 0.78" Height
|
|
Insert
|
PBT
|
|
Contacts
|
Brass Alloy
|
|
Contact Surface
|
Gold Plated Nickel
|
|
Orientation
|
Female
|
|
Cable Range
|
5 - 9 mm (.2"- .35")
|
|
Contact Count
|
10
|
|
Crimp Wire Gauge
|
28-18 AWG
|
|
Operating Temperature
|
-40 F to 257 F (-40 C to 125 C).
|
|
Nominal Current
|
8 Amps
|
|
Nominal Voltage
|
160V
|
|
Min. Mating Cycles
|
>1000
|
|
Insulation Resistance
|
>10^6 MOhm
|
|
Max. Contact Resistance
|
3 mOhm
|
|
Mating Thread
|
M16
|
|
Type of Connection
|
Crimp Contact
|
|
IP Protection
|
IP67 / IP69K
|
📋 Basic Assembly Overview
1. Verify Components: Confirm the housing, insert, and crimp contacts match the required pin count, contact size, and cable diameter.
2. Prepare Cable: Strip the cable jacket and conductors to the correct length for the crimp contacts being used.
3. Crimp Contacts: Crimp each socket contact to the specified wire gauge and inspect the termination before insertion.
4. Seat Contacts: Insert the contacts into the insert and verify the Euro-Lock system keeps them in position.
5. Final Assembly: Install the insert into the housing, tighten the cable seal, and confirm the connector is ready for the mating M16 interface.
Always follow the applicable Sealcon assembly instructions and verify the connector configuration before applying power.
📦 What's Included
• Housing - (1) 5-9 mm (.2"-.35") Cable O.D. (P/N S7.847.400.000)
• Insert - (1) 10 Pin, 8 A, 160V, for crimp contacts (P/N S7.003.910.102)
• Contacts - (10) 28-18 AWG 1 mm Crimp Sockets (P/N S7.010.981.002 )
📞 Sealcon Support
Housing, insert, and crimp contacts can be sold separately. Custom configurations are also available. Contact us at 800-966-2345 for more information.
Note: Image is for reference only; actual product may differ.
|
|
|
 |
|
 |
|
