 |
Meltric 33-18163 DS20 Male Inlet, 208V AC, 20 Amps
DS20 male inlet rated for 208V AC and 20 Amps, 3 Pole + Ground configuration, 14-8 AWG wiring capacity, fiberglass-reinforced thermoplastic body, Type 3R, IP 54.
Why Choose the Meltric 33-18163 DS20 Male Inlet?
The Meltric 33-18163 DS20 male inlet is built for industrial DS Series power connections where a compact, durable inlet is required. It is rated for 208V AC and 20 Amps and uses a 3 pole + ground with 14-8 AWG wiring capacity.
Its impact-resistant blue thermoplastic polyester body is reinforced with fiberglass to help withstand chemical exposure, UV radiation, and daily plant-floor use. Silver-nickel contacts support reliable conductivity during repeated connecting and disconnecting, while the DS Series design helps reduce arc-flash risk when used with the correct mating device.
⚡ 20A DS20 Inlet
Rated for 20 Amps and 208V AC service
🔌 Polarity Match
3 Pole + Ground for matching DS Series connections
🧰 Screw Terminals
Accepts 14-8 AWG conductors for field wiring
🛡️ Industrial Housing
Type 3R, IP 54 (Partial protection from dust, and splashing water from any direction) with 100kA Close & Withstand performance
⚠️ Confirm Voltage, Polarity, and Matching Receptacle
Before ordering, confirm the required voltage, amperage, polarity, horsepower rating, environmental rating, and matching Meltric DS Series female receptacle. This inlet should be installed only by qualified personnel following applicable electrical codes and the Meltric DS Series instructions.
Note: Image is for reference, actual part may differ. Ground shipping only.
📋 Safety and Contact Design
The DS Series 33-18163 male inlet is designed for branch-circuit and motor-circuit disconnect switching when paired with the proper mating device. It uses silver-nickel contacts made from an 85% silver and 15% nickel combination, helping maintain a durable, conductive contact point even through repeated connection cycles.
Switch Rating: Branch Circuit & Motor Circuit Disconnect Switching
Short Circuit Rating: 100kA Close & Withstand
Environmental Rating: Type 3R, IP 54 (Partial protection from dust, and splashing water from any direction)
Key Features & Benefits
- Rated for 208V AC and 20 Amps
- 3 Pole + Ground polarity
- Screw terminals with 14-8 AWG wiring capacity
- Compact 2.6" diameter x 2.55" depth housing
- Blue thermoplastic polyester body reinforced with fiberglass
- Silver-nickel contacts for durable conductivity during repeated mating cycles
- IK09 impact rating
- UL, CSA listed
- Designed for use with a compatible Meltric DS Series female receptacle
Technical Specifications
|
Product Code
|
33-18163
|
|
Rated Voltage
|
208V AC
|
|
Rated Current
|
20 Amps
|
|
Overall Dimensions
|
2.6" Diameter x 2.55" Depth
|
|
Polarity
|
3 Pole + Ground
|
|
Horsepower
|
3 hp
|
|
Switch Rating (AC only)
|
Branch Circuit & Motor Circuit Disconnect Switching
|
|
Short Circuit Rating
|
100kA Close & Withstand
|
|
Temperature Range
|
-40 F to 140 F (-40 C to 60 C)
|
|
Wiring Capacity
|
14-8 AWG
|
|
Terminal Type
|
Screw
|
|
Impact Rating
|
IK09
|
|
Environmental Rating
|
Type 3R, IP 54 (Partial protection from dust, and splashing water from any direction)
|
|
Listings
|
UL, CSA
|
📋 Basic Installation Overview
1. Verify Ratings: Match the inlet to the correct voltage, current, polarity, and horsepower requirements before installation.
2. Confirm Mating Device: Use this male inlet with the proper Meltric DS Series female receptacle or compatible mating component.
3. Prepare Conductors: Use conductors within the listed 14-8 AWG wiring capacity and terminate them to the screw terminals according to the manual.
4. Check Environment: Confirm that the Type 3R / IP54 rating is suitable for the installation location and exposure level.
5. Test Before Service: Inspect wiring, grounding, mounting, and mating alignment before energizing the circuit.
Always follow the Meltric DS Series user manual and local electrical code requirements before operation.
📞 Meltric DS Series Resource
Meltric DS Series User Manual:
Use the manual to confirm wiring, mating compatibility, installation requirements, and safety procedures for DS Series devices.
|
|
|
